![]() ![]() switch SATA-Option in UEFI/BIOS between IDE and AHCI.plug SSD to another SATA-Port on Mainboard.Hdparm -user-master m -security-set-pass NEWPASS /dev/sda all possible commands in the Linux terminal (see above) - including Royce' command:.It's connected directly to the motherboard via SATA-connection.Įxplanation for my assumption it's a hardware problem:ġ) I've tried everything that is possible on the software-level - and nothing worked for the ssd: > No, it's not conected via USB-to-SATA. (Explanation for this in this post further wouldn't happen to be attaching the drive via USB-to-SATA, would you? If so, can you try with a direct SATA connection? I will contact Crucial to - hopefully - get the SSD replaced. I think there's no doubt that it is a hardware problem. *In a general service mail that i sent before the staff was very helpful, even by mentioning Linux. Just say it doesn't work with Windows 10, and you are good to go. SO - my tip: if you send it back just don't mention something about using it with Linux (at least in the actual replacement request*). I got the impression that they tried to blame me, instead of listening to my statement that i did nothing wrong and it has to be a hardware failure. And actually one guy told me something like "the drive is not beeing replaced if the drive got bricked whilst using Linux". They said something like: "we don't support Linux" (which is - in my opinion - idiocy and not to heard to). My experience: - Crucial tries to get rid of you (at least on telephone) when you say you use this drive with Linux and then the problem occured. Ok guys, the replacement WORKED! I encourage everyone who runs into the same problem to send Crucial a warranty replacement request. Maybe i'll confront Crucial with that info in the next days.Īnd for further information: I've tried the following commands, too: hdparm -user-master m - security-disable NULL /dev/sdaĪnd hdparm -user-master m -security-erase-enhanced NULL /dev/sda In his case - they assume - there are controller-problems. I've found this thread today where someone has the exact same problem. I’m a little bit desperate right here, hope you can help. Maybe that led to the locked-state? I don’t know. I solved that by putting the system in Sleep Mode. Maybe important to know: Before that my drive has been frozen. Hdparm -user-master u -security-erase PASS /dev/sdaīut it said the following with some and some more 00’s) at the end: Bad/missing sense data, sb: 70 00 05 00 00 00 00 0a 51 e0 00 21 04 … I've booted from a Knoppix Live CD and used the command: hdparm -user-master u -security-set-pass PASS /dev/sdaĪfter that I wanted to actually secure erase it with: Or maybe someone knows another solution that could unlock my SSD.īackground: I wanted to secure erase my SSD drive. I want to use the command: hdparm -user-master m -security-unlock PASS /dev/sda Does someone know the ATA master password for Crucial drives? Unfortunately I haven’t found the master ATA password for Crucial drives on the internet. So I’ve searched all over google, and read in a thread that I should try to unlock it with the master password. I can’t unlock it with the correct (!) user password. The SSD will not be usable as a normal drive, but the user should be able to retrieve storedĭata and transfer to a new device.My Crucial BX100 SSD is locked. When Attribute 180 reaches 0, the firmware will place This number decreases as the number of retired blocks increases. ![]() ![]() This number varies based on the underlying NAND architecture, the firmware architecture, and the user capacity of the drive, "Attribute 180: Unused Reserved Block Count (Available Spare Blocks on PCIe SSDs)Īgain, as the name implies, this is the count of extra blocks available to be used in case bad blocks need to be retired. I go to Crucial's website and of course they confused me even more: Both are new drives and shows only 1 power cycle. When I check SMART one drive says Unused Reserved Block Count is 44 while the other drive is 37. I just got two 500 GB Crucial MX500 SSDs. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |